Test Your Electrical Safety Knowledge

What should be done if you see a power tool's plug with a missing center ground prong?

Tag the tool before use

Do not use it

Use the tool as it is normal

Use the tool because the plug is still safe

Correct! Wrong!

Which of the following would be the most likely indication of an electrical circuit overload condition?

equipment fails to start

notification by OSHA

excess noise in the circuit

excess heat or arcing

Correct! Wrong!

Which of the following is the lowest level of electrical current that can cause heart fibrillation and death?

50-150 milliamps

15 amps

10 amps

5-10 milliamps

Correct! Wrong!

OSHA standards require that exposed or operating elements of an electrical installation be constructed and installed to _____.

Minimize workplace electrical dangers

Comply with the globally harmonized system

Warn workers of electrical hazards

NIOSH/CDC standards

Correct! Wrong!

A short thin piece of wire which is heated up and melt by the flowing of electric current in it, is called

Fuse

Resistor

Circuit

Cell

Correct! Wrong!

Insulating equipment, such as electrical protective gloves, found defective must be _____.

checked and used carefully

taken out of service until repaired and retested

thrown away and never used again

evaluated for changes in color or texture

Correct! Wrong!

Each of the following are well-known examples of circuit protection devices, EXCEPT:

capacitors.

ground Fault Circuit Interrupters (GFCI).

circuit breakers.

fuses.

Correct! Wrong!

Which of the following procedures protects the electrician from accidental or unexpected equipment startup?

Using a "buddy system" during maintenance

Electrical release procedures

Continual monitoring of equipment status

Lockout/tagout procedures

Correct! Wrong!

What is the first step toward protecting yourself from the many electrical hazards you may face on the job?

Knowing how to respond

Recognizing hazards

Reporting accidents

Complying with OSHA

Correct! Wrong!

What are the most common injuries due to electrical hazards?

Impact

Burns

Shocks

Falls

Correct! Wrong!

What should you do if you find a person who is "frozen" to an energized electrical surface or wire?

Turn the power off immediately

Nothing, it's too late

Pull the person off the point of contact

Try to yank the person away from the contact point

Correct! Wrong!

Why is static electricity a serious potential hazard?

It can result in unintentional impact

It can surprise the worker causing an injury

It can disrupt neurological pathways

It can cause a fire or explosion

Correct! Wrong!

Which of the following is the unit used to measure the resistance to the flow of electrical current?

Volt

Newton

Ampere

Ohm

Correct! Wrong!

All of the following determine the severity of an electrical shock, EXCEPT:

the current's frequency.

the path through the body.

the degree of electrical decay.

the amount of current flow.

Correct! Wrong!

Test Your Electrical Safety Knowledge

I Got 6% Marks In Electrical Safety Knowledge Quiz | Very Poor

You score is very poor in electrical safety knowledge quiz, you can do better, try again.

I Got 13% Marks In Electrical Safety Knowledge Quiz | Very Poor

You score is very poor in electrical safety knowledge quiz, you can do better, try again.

I Got 20% Marks In Electrical Safety Knowledge Quiz | Poor

You score is poor in electrical safety knowledge quiz, you can do better, try again.

I Got 26% Marks In Electrical Safety Knowledge Quiz | Poor

You score is poor in electrical safety knowledge quiz, you can do better, try again.

I Got 33% Marks In Electrical Safety Knowledge Quiz | Poor

You score is poor in electrical safety knowledge quiz, you can do better, try again.

I Got 40% Marks In Electrical Safety Knowledge Quiz | Poor

You score is poor in electrical safety knowledge quiz, you can do better, try again.

I Got 46% Marks In Electrical Safety Knowledge Quiz | Fair

You score is fair in electrical safety knowledge quiz, you can do better, try again.

I Got 53% Marks In Electrical Safety Knowledge Quiz | Fair

You score is fair in electrical safety knowledge quiz, you can do better, try again.

I Got 60% Marks In Electrical Safety Knowledge Quiz | Good

You score is good in electrical safety knowledge quiz, you can do better, try again.

I Got 66% Marks In Electrical Safety Knowledge Quiz | Good

You score is good in electrical safety knowledge quiz, you can do better, try again.

I Got 73% Marks In Electrical Safety Knowledge Quiz | Very Good

You score is very good in electrical safety knowledge quiz, you can do better, try again.

I Got 80% Marks In Electrical Safety Knowledge Quiz | Very Good

You score is very good in electrical safety knowledge quiz, you can do better, try again.

I Got 86% Marks In Electrical Safety Knowledge Quiz | Very Good

You score is very good in electrical safety knowledge quiz, you can do better, try again.

I Got 93% Marks In Electrical Safety Knowledge Quiz | Excellent

You score is excellent in electrical safety knowledge quiz, you can do better, try again.

I Got 100% Marks In Electrical Safety Knowledge Quiz | Excellent

You score is excellent in electrical safety knowledge quiz

Test Your Electrical Safety Knowledge | MCQs Test

What should be done if you see a power tool's plug with a missing center ground prong?

Which of the following would be the most likely indication of an electrical circuit overload condition?

Which of the following is the lowest level of electrical current that can cause heart fibrillation and death?

OSHA standards require that exposed or operating elements of an electrical installation be constructed and installed to _____.

A short thin piece of wire which is heated up and melt by the flowing of electric current in it, is called

Insulating equipment, such as electrical protective gloves, found defective must be _____.

Each of the following are well-known examples of circuit protection devices, EXCEPT:

Which of the following procedures protects the electrician from accidental or unexpected equipment startup?

What is the first step toward protecting yourself from the many electrical hazards you may face on the job?

What are the most common injuries due to electrical hazards?

What should you do if you find a person who is "frozen" to an energized electrical surface or wire?

Why is static electricity a serious potential hazard?

Which of the following is the unit used to measure the resistance to the flow of electrical current?

All of the following determine the severity of an electrical shock, EXCEPT:

Test Your Knowledge Of Crane Safety

Test Your Work At Height Safety Knowledge | MCQs Test

Learn About The Procedures Involved In PAT Testing

Test Your Knowledge Of Accident Investigation | MCQs Test

Walking Working Surfaces and Fall Protection Quiz | MCQs Test

How Does Water Affect the Flow of Electricity?

One Comment

Leave a Reply Cancel reply

What should be done if you see a power tool's plug with a missing center ground prong?

Which of the following would be the most likely indication of an electrical circuit overload condition?

Which of the following is the lowest level of electrical current that can cause heart fibrillation and death?

OSHA standards require that exposed or operating elements of an electrical installation be constructed and installed to _____.

A short thin piece of wire which is heated up and melt by the flowing of electric current in it, is called

Insulating equipment, such as electrical protective gloves, found defective must be _____.

Each of the following are well-known examples of circuit protection devices, EXCEPT:

Which of the following procedures protects the electrician from accidental or unexpected equipment startup?

What is the first step toward protecting yourself from the many electrical hazards you may face on the job?

What are the most common injuries due to electrical hazards?

What should you do if you find a person who is "frozen" to an energized electrical surface or wire?

Why is static electricity a serious potential hazard?

Which of the following is the unit used to measure the resistance to the flow of electrical current?

All of the following determine the severity of an electrical shock, EXCEPT:

Similar Posts

One Comment

Leave a Reply Cancel reply