Fatality Rate Calculator
Fatality Rate · per million hours
Work-related deaths per 1,000,000 hours worked — the most severe lagging indicator. Zero is the only acceptable target. Pair with LTIFR, TRIFR, and leading measures such as NMFR. Same period for both inputs.
Formula: Fatality Rate = (Fatalities × 1,000,000) ÷ Total Hours Worked
- Zero fatalities is the only acceptable target — a low rate is not “good performance” if anyone died.
- Use one work-related definition and the same hour scope as your other HSE rates.
- Do not mix million-hour fatality rate with OSHA 200,000-hour rates without converting (÷ or × 5).
What is a Fatality Rate?
The Fatality Rate measures how often work-related deaths occur relative to hours worked. It is the most severe lagging safety metric: it counts harm after it has happened.
Organizations, regulators, and HSE teams use it to track mortality risk over time, compare operations on a common base, and demonstrate accountability. It sits alongside rates such as LTIFR, TRIFR, and AFR — and should always be paired with leading indicators like NMFR.
Why Fatality Rate matters
- Zero harm focus — any workplace death is a critical failure, not a decimal to minimise on a dashboard
- Regulatory and stakeholder accountability — OSHA, ILO, boards, and clients expect transparent fatality reporting
- High-risk identification — elevated rates highlight sectors, tasks, or sites needing intervention
- Learning after tragedy — investigation quality and systemic fixes matter more than the rate alone
Important: a small per-million figure after a fatality is not “good performance.” Large hour bases can make rates look tiny while a person has still died.
Fatality Rate formula
The standard million-hour formula is:
Fatality Rate = (Number of Fatalities × 1,000,000) ÷ Total Hours Worked
- Fatalities — work-related deaths in the period (use one written definition)
- Total Hours Worked — employee (and, if in scope, contractor) hours for the same period
- 1,000,000 — normalises the rate per million hours
Worked example
An organisation records 1 work-related fatality and 10,000,000 hours worked:
Fatality Rate = (1 × 1,000,000) ÷ 10,000,000 = 0.10
OSHA-style equivalent (per 200,000 hours) = 0.10 ÷ 5 = 0.02. Always state which base you used. The human meaning of that number is one life lost — not a “low” score.
How to read your Fatality Rate
Guidance below is indicative. Definitions, contractor scope, and workforce size change the picture. Fatal events are rare, so rates for small sites can swing sharply year to year.
- 0 — the only acceptable target for the period
- > 0 — critical; investigate, support families, and fix systemic causes
- Often ≥ 0.1–1+ — especially severe relative frequency for many sectors
Never use Fatality Rate as a casual KPI traffic light. Multi-year trends, peer comparisons with matching definitions, and serious-injury precursors matter more than a single decimal.
Fatality Rate vs other HSE rates
| Metric | What it counts | Typical base | Acceptable target |
|---|---|---|---|
| Fatality Rate | Work-related deaths | 1,000,000 hours | Zero |
| LTIFR | Lost-time injuries | 1,000,000 hours | As low as practicable |
| TRIFR | Recordable / total injuries | 1,000,000 hours | As low as practicable |
| NMFR | Near misses reported | 1,000,000 hours | Higher reporting often healthier |
Reducing workplace fatalities
- Control life-critical risks — falls from height, vehicle–pedestrian conflict, energy isolation, confined space, struck-by
- Enforce protocols and competence — training, permits, and supervision matched to the hazard
- Use hierarchy of controls — eliminate and engineer before relying on PPE alone
- Investigate near misses and SIFs — serious injury and fatality potential events deserve the same rigor as actual fatalities
- Lead visibly — stop work authority, fatigue management, and contractor interface controls
FAQ
What counts as a work-related fatality?
A death arising from a workplace accident or occupational exposure as defined in your jurisdiction and company procedure. Align with the same rules you use for regulatory reporting.
Is a fatality rate of 0.05 “good”?
No. If the numerator is greater than zero, someone died. The decimal only reflects hours in the denominator. Treat every fatality as unacceptable.
Can I compare to OSHA rates?
Yes for presentation: divide the million-hour rate by 5 for a per-200,000-hours figure (or multiply the OSHA-style figure by 5). Label the base clearly.
Should contractors be included?
Match your other rate scope. If contractors are in LTIFR/TRIFR, include their fatalities and hours the same way — or report a separate contractor fatality rate.
Why can my rate jump after one death?
Fatalities are rare. On a smaller hour base, a single event moves the rate a lot. Report multi-year averages alongside the annual figure when communicating with leadership.
Related tools: LTIFR Calculator, TRIFR Calculator, Severity Rate Calculator, NMFR Calculator.
