In Great Britain, an employer must assess work that could put employees at risk from hand-arm vibration and eliminate that risk at source or reduce it as far as reasonably practicable. Two daily exposure values determine further action. If an employee is likely to reach 2.5 m/s² A(8) and elimination is not reasonably practicable, put a programme of controls into effect. Plan the work so that exposure stays within the 5 m/s² A(8) limit. A reading below the action value still calls for action if the work presents a health risk. Control of Vibration at Work Regulations 2005, regulations 4–7
These duties cover vibration transmitted through the hands, whether an employee uses a powered tool, guides a vibrating machine or holds a workpiece against vibrating equipment. Repeated exposure can damage nerves and blood vessels, causing hand-arm vibration syndrome (HAVS). The rules discussed here apply in England, Scotland and Wales. Northern Ireland has its own Control of Vibration at Work Regulations.
Establish who is exposed and what their working day involves
The assessment starts when the work could put an employee’s health at risk. Watch the job being done and ask operators about the parts of the day you might miss, including short finishing jobs, shared tools and unusually heavy workloads. The same tool can give two operators different daily exposures because the time in contact with vibration differs. Regulation 5 sets out what the assessment must cover.
- Identify the person, task and source. Include all the vibrating tools, machines and workpieces the person handles during a working day. Record the material, accessory and condition of the equipment. Ask about repeated impacts, cold conditions and any occupational-health advice that calls for extra protection.
- Find a representative vibration level. Use reliable data for the equipment doing comparable work. Check whether a supplier’s figure covers the same process, accessory and operating conditions. If the available information cannot support a reliable estimate, arrange competent measurement.
- Observe the actual exposure time. Count the time the operating tool or vibrating workpiece is in contact with the hands. Include repeated bursts. Separate running time in contact with the hands from set-up, marking out and other parts of the job with no exposure.
- Combine the day’s tasks for each employee. A(8) expresses daily exposure on an eight-hour reference basis, whatever the length of the shift. Enter each representative vibration level and its exposure time separately in the Health and Safety Executive (HSE) exposure calculator. Use the combined daily result. Adding the tools’ vibration magnitudes gives the wrong quantity.
A tool timer can help establish exposure time. The vibration magnitude used alongside that time still needs to represent the actual job. There is no general duty to issue everyone with a wearable monitor or continuously log every shift. Check the estimate where work varies, and act on a known risk while improving the data. HSE guidance on measurement and monitoring
Decide what the daily exposure requires
Compare the employee’s total for the day with the action value and limit value. Plan the control programme as soon as the action value is likely to be reached. The limit value is the daily ceiling in ordinary work, so reaching it leaves no room for further vibration exposure that day. In HSE’s calculator the two values correspond to 100 and 400 exposure points respectively. HSE guidance on the two exposure values
| Assessment finding | Action to take |
|---|---|
| Below 2.5 m/s² A(8) | Continue to eliminate or reduce any identified risk. Take account of workers at particular risk and follow up reports of symptoms even when the estimate is below the action value. |
| Likely to reach or exceed 2.5 m/s² A(8) | If elimination at source is not reasonably practicable, implement a programme to reduce exposure as far as reasonably practicable. Arrange appropriate health surveillance and provide information, instruction and training. |
| Likely to exceed 5 m/s² A(8) | Change the work before the employee exceeds the limit. Replan the method, equipment or remaining tasks, allowing for exposure already received that day. |
| Already above 5 m/s² A(8) | Take immediate action to reduce exposure below the limit, identify why the exceedance happened and change the controls to prevent a recurrence. End further vibration exposure for that employee that day. A break cannot undo exposure already received. |
Can an employer average a high day across the week? Regulation 6(5) allows this only where exposure is usually below the action value, varies markedly and may occasionally exceed the daily limit. The weekly exposure calculated under Schedule 1 must be below the limit. The employer also needs evidence that this pattern presents less risk than constant exposure at the limit, must reduce risk as far as reasonably practicable in the special circumstances, and must provide increased health surveillance where appropriate. Keep the evidence for every condition if the employer relies on this exception. Regulation 6(4)–(6)
Put the control programme into practice
Start with the work creating the greatest exposure. Give each action an owner and a completion date, and say what protection will apply until it is complete. Ask the operator and the safety representative whether the proposed method will work with the actual material, access and production demands. HSE guidance on recording the risk assessment and action plan
- Remove vibration from the hands where possible. Consider changing the process or mechanising the task so that an employee no longer needs to hold the tool or workpiece while it vibrates.
- Choose and maintain equipment for the job. Check the exposure over the time it takes to finish the work. A low-vibration tool that cuts too slowly can increase contact time. Match the tool and accessory to the task, replace worn consumables and make it clear who takes a defective tool out of use. See how to choose low-vibration power tools.
- Change the way people work. Use supports or fixtures where they reduce the force needed to grip or guide the work. Organise breaks and alternate with tasks that give the hands a genuine break from vibration. Check each worker’s combined exposure before relying on rotation.
- Check the result with the people using it. Observe the revised task, check contact time and ask about grip, discomfort and equipment condition. Recalculate the daily exposure when inputs change. Gloves can keep hands warm and dry. Do not rely on gloves sold as anti-vibration protection to reduce exposure. Control the vibration through the process, equipment and way the job is done.
HSE’s guidance on practical controls for employers covers purchasing, maintenance, workplace layout, work schedules and warm clothing. Keep a record of the control actually introduced and how you checked that it worked.
Train employees and arrange health surveillance
Employers must train employees and their representatives if the assessment identifies a risk to health or employees are likely to reach or exceed the exposure action value. Explain the assessment findings, what the two values mean, the controls for the job, and how to recognise and report early symptoms such as tingling, numb fingers or fingers turning white in the cold. Tell workers how to access health surveillance and why it matters. Update the training after significant changes to the work or methods. Make sure anyone carrying out duties for the employer, including a supervisor or external assessor, has the instruction and training their task requires. Regulation 8 on information, instruction and training
Discuss proposed controls and health surveillance with the trade union safety representative or employee representative. Show operators how to use the equipment and who to tell about a rough-running tool or symptoms between scheduled checks. Share collective surveillance findings in a form that protects individuals’ identities. HSE summary of employer responsibilities
The same two triggers apply to suitable health surveillance where it is appropriate. Under regulation 7, this means there is an identifiable health effect linked to exposure, it is probable under the employee’s working conditions, and valid techniques exist for detecting it. Get occupational-health advice about who needs surveillance, including anyone particularly susceptible below the action value. Arrange it during working hours at the employer’s expense. An employee who reports symptoms should be referred promptly, even if the next routine check is months away. Regulation 7 on health surveillance
Act on health findings and keep the right records
A report of tingling is enough to investigate the work and arrange appropriate follow-up. A finding by a doctor or occupational-health professional that a disease or adverse effect resulted from vibration exposure brings further duties. Make sure a suitably qualified person explains the finding and follow-up to the employee. Review the risk assessment and controls, act on professional advice, and consider alternative work without further vibration risk. Arrange a review of other similarly exposed employees’ health, including a medical examination where recommended. Regulation 7(5) of the Control of Vibration at Work Regulations
Check whether a disease report is required. Under the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 2013 (RIDDOR), report a doctor’s written diagnosis of HAVS in an employee whose work involves regular use of percussive or vibrating tools, or holding material subjected to percussion or vibration. A written diagnosis of carpal tunnel syndrome is reportable where the employee’s work involves regular use of percussive or vibrating tools. Submit the report as soon as the diagnosis is received if the work criteria are met. RIDDOR regulation 8(a) and (d) and HSE reporting times.
Keep records that show how the workplace is controlled and how individual restrictions will be put into practice.
- What needs changing at work? Record the significant findings as soon as practicable after making or changing the assessment. Keep the exposure basis, controls and training already in place, planned actions, owners and follow-up checks. Review the assessment regularly and immediately if there is reason to doubt its validity or the work changes significantly. Revise it where necessary. Regulation 5(4)–(5)
- What work can the individual undertake? Maintain a health record for each employee under surveillance. Include their exposure history, fitness for work and any agreed restrictions. Allow the employee access on reasonable notice and provide copies to the enforcing authority when required. Occupational health holds the confidential clinical notes. Give supervisors the restrictions they need to allocate work safely. HSE L140, paragraphs 193–195




